Mocom Milldrop Specifications Page 86
- Page / 102
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
APPENDIX E – ALARMS
80
APPENDIX E – ALARMS
INTRODUCTION
Every time an anomalous condition occurs during the operation of the sterilizer, an alarm is
generated, identified by a specific code
(consisting of a letter followed by a 3-digit number).
Alarm codes are divided into three categories
:
• E = ERROR
Wrong maneuver and/or use, or a cause external to the device.
A problem that can generally be fixed by the user.
Code format: Exxx (xxx = identifying number from 000 ÷ 999)
• A = ALARM
First-level
fault, not linked to safety.
A problem that normally is fixed by a specialized technician on-site.
Code format: Axxx (xxx = identifying number from 000 ÷ 999)
• H = HAZARD
Second-level
fault, linked to safety.
A problem generally fixed by the Technical Support Center.
Code format: Hxxx (xxx = identifying number from 000 ÷ 999)
ALARM
INTERVENTION
Alarm during a cycle
NOTE
I
N THE CASE OF AN ALARM, PLEASE ONLY REMOVE VOLTAGE FROM THE DEVICE AFTER
EXECUTING A RESET
(SEE THE PARAGRAPH, “RESETTING THE SYSTEM”).
The intervention of the alarm causes the interruption of the cycle (or the normal equipment
operation) with the relative appearance of an alarm code and a message on the display,
accompanied by a beep and the lit alarm icon (intermittent).
NOTE
D
URING THE ALARM PROCEDURE, THE DISPLAY ALWAYS SHOWS THE CURRENT
TEMPERATURE AND PRESSURE IN THE STERILIZATION CHAMBER
.
This procedure is designed so as not
to allow the user to mistake an anomalous cycle for a
correctly completed cycle and, as a consequence, involuntarily using non-sterile material
.
The alarm procedure is differentiated depending on whether it occurs during the execution of
the program or outside
, and is structured to guide the user to the necessary RESET of the
sterilizer.
If the alarm intervenes during a program, the display will show the message:
(Alarm Message)
LEVELLING
114.6°CXXXX
0.70 bar11:30
Whenever an alarm is generated in certain phases of the cycle, an automatic procedure is
activated to clean the internal water circuit. The display will contain the notice:
(Alarm Message)
CIRCUIT CLEANING
100.6°CXXXX
0.70 bar11:40
A
larm Message
A
larm Code
A
larm Code
- REVISIONS 3
- TABLE OF CONTENTS 3
- PURPOSE OF THE 8
- MANUAL 8
- GENERAL 8
- WARNINGS 8
- CONTENTS OF 9
- THE PACKAGE 9
- HANDLING THE 10
- PRODUCT 10
- INTRODUCTION 11
- CONTROL 14
- LCD DISPLAY 14
- OPERATING 15
- CYCLE EXAMPLE 15
- INSTALLATION 16
- EXTENSION CORDS 17
- MANAGING THE 18
- FILES BY 18
- MILLFLASH SW 18
- FIRST START-UP 23
- STAND-BY MODE 24
- FILLING DISTILLED 25
- MAX LEVEL IN THE 26
- INTERNAL/ 26
- EXTERNAL DRAIN 26
- CONFIGURATION 27
- MILLENNIUM 28
- DESCRIPTION OF 29
- THE MENU ITEMS 29
- DEFAULTS 31
- SETTINGS 31
- ACTIVATING 31
- OPTIONS 31
- DISABLED+ 32
- 134 °C HOLLOW+ 33
- STANDARD DRYING+ 34
- 134°C PROCESS+ 35
- FRACTION. VACUUM + 35
- SHORT DRYING+ 35
- STANDARD DRYING+ 36
- ST‐ BY MODE+ 37
- OFF+ 37
- PRINTER+ 38
- OFF+ 38
- TYPE 1 + 38
- CR TYPE+ 38
- PRINTOUT MODE+ 39
- AT CYCLE END+ 39
- NORMAL PRINT+ 39
- AUTOMAT. FILLING + 40
- INTERNAL DRAIN+ 40
- EXIT THE 42
- PREPARING THE 43
- MATERIAL 43
- ARRANGING THE 44
- 134°C POROUS 46
- STERILIZATION CYCLE 47
- RUNNING 48
- THE CYCLE 48
- 134°C B CYCLE 49
- Standard drying 52
- Intelligent drying 52
- EXTRA DRYING 52
- (+XX) is the time 52
- RESULT OF THE 53
- CYCLE 53
- CHECK OF THE 54
- CYCLE DATA 54
- REPORT 54
- MANUAL CYCLE 54
- INTERRUPTION 54
- SEE APPENDIX E “ALARMS” 55
- STORING 56
- STERILIZED 56
- MATERIALS 56
- TEST PROGRAMS 57
- PRINTING REPORTS 58
- SUMMARY TABLE 61
- SAFETY DEVICES 62
- WATER SUPPLY CHARACTERISTICS 63
- APPENDIX B – PROGRAMS 64
- APPENDIX B – PROGRAMS 65
- 60 66
- 121c POROUS 69
- 121c HOLLOW 70
- 134c EMERGENCY 73
- 134°C - 3'00'' 73
- VACUUM TEST (VT) 74
- -0.80 bar 74
- EXAMPLES OF PRINTED REPORTS 75
- APPENDIX C – MAINTENANCE 77
- QUALITY DEMINERALIZED 78
- MAINTENANCE 79
- DESCRIPTION 79
- THE COMPONENT 81
- PERIODIC 82
- STERILIZER 82
- VALIDATION 82
- DISPOSAL AT END 82
- PROVIDING THE MODEL 85
- APPENDIX E – ALARMS 86
- RESETTING THE 88
- SYSTEM 88
- ALARM CODES 89
- DICHIARAZIONE DI CONFORMITÀ 97
- TECHNICAL SUPPORT DEPARTMENT 102
© 2020, manymanuals.com. All rights reserved. | 0.983 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals