Mocom Milldrop Specifications Page 77
- Page / 102
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
APPENDIX C – MAINTENANCE
71
APPENDIX C – MAINTENANCE
In addition to correct use, the user needs to perform ordinary maintenance in order to guarantee safe, efficient operation
over the device's entire life.
INTRODUCTION
For better quality maintenance, supplement ordinary checks with regular periodic
examinations by the service department (see Appendix Z).
It is also fundamental to perform a periodic sterilizer validation, i.e., a check of the
thermodynamic parameters of the process, comparing them with the reference values
provided with suitably calibrated instruments. In this regard, see the paragraph, “Periodic
Sterilizer's Validation”, further below in this Appendix.
The ordinary maintenance described below consists in easy manual operations and preventive
interventions involving simple instruments.
WARNING
IN THE EVENT OF THE REPLACEMENT OF THE DEVICE'S COMPONENTS
OR PARTS, REQUEST AND/OR USE ORIGINAL REPLACEMENT PARTS
ONLY.
ORDINARY
MAINTENANCE
PROGRAM
Scheduled Maintenance
Messages
The table summarizes the maintenance required to keep the sterilizer operating at peak
efficiency. In the case of very intense use
, we recommend shortening maintenance
intervals:
DAILY
Clean the gasket on the porthole
Clean external surfaces
WEEKLY Clean the sterilization chamber and relative accessories
Disinfect external surfaces
MONTHLY Clean the internal (and external - if installed) distilled water tank
Safety valve maintenance
Clean (or replace) the drain filter
ANNUALLY
Validate sterilizer (see dedicated paragraph)
The steriliser periodically reminds the user about necessary "routine" maintenance operations
that must be carried out in order to ensure the proper operation of the device.
The alert notices are displayed on the screen in the following way when the pre-selected
sterilisation cycle is started:
(ALERT MESSAGES)
↵ to confirm
⇑ to delay
Push the ↵ key to confirm the execution of the maintenance operation.
Press the ⇑ key to postpone the operation.
In this case, the user is reminded with another message the next time the steriliser is used.
- REVISIONS 3
- TABLE OF CONTENTS 3
- PURPOSE OF THE 8
- MANUAL 8
- GENERAL 8
- WARNINGS 8
- CONTENTS OF 9
- THE PACKAGE 9
- HANDLING THE 10
- PRODUCT 10
- INTRODUCTION 11
- CONTROL 14
- LCD DISPLAY 14
- OPERATING 15
- CYCLE EXAMPLE 15
- INSTALLATION 16
- EXTENSION CORDS 17
- MANAGING THE 18
- FILES BY 18
- MILLFLASH SW 18
- FIRST START-UP 23
- STAND-BY MODE 24
- FILLING DISTILLED 25
- MAX LEVEL IN THE 26
- INTERNAL/ 26
- EXTERNAL DRAIN 26
- CONFIGURATION 27
- MILLENNIUM 28
- DESCRIPTION OF 29
- THE MENU ITEMS 29
- DEFAULTS 31
- SETTINGS 31
- ACTIVATING 31
- OPTIONS 31
- DISABLED+ 32
- 134 °C HOLLOW+ 33
- STANDARD DRYING+ 34
- 134°C PROCESS+ 35
- FRACTION. VACUUM + 35
- SHORT DRYING+ 35
- STANDARD DRYING+ 36
- ST‐ BY MODE+ 37
- OFF+ 37
- PRINTER+ 38
- OFF+ 38
- TYPE 1 + 38
- CR TYPE+ 38
- PRINTOUT MODE+ 39
- AT CYCLE END+ 39
- NORMAL PRINT+ 39
- AUTOMAT. FILLING + 40
- INTERNAL DRAIN+ 40
- EXIT THE 42
- PREPARING THE 43
- MATERIAL 43
- ARRANGING THE 44
- 134°C POROUS 46
- STERILIZATION CYCLE 47
- RUNNING 48
- THE CYCLE 48
- 134°C B CYCLE 49
- Standard drying 52
- Intelligent drying 52
- EXTRA DRYING 52
- (+XX) is the time 52
- RESULT OF THE 53
- CYCLE 53
- CHECK OF THE 54
- CYCLE DATA 54
- REPORT 54
- MANUAL CYCLE 54
- INTERRUPTION 54
- SEE APPENDIX E “ALARMS” 55
- STORING 56
- STERILIZED 56
- MATERIALS 56
- TEST PROGRAMS 57
- PRINTING REPORTS 58
- SUMMARY TABLE 61
- SAFETY DEVICES 62
- WATER SUPPLY CHARACTERISTICS 63
- APPENDIX B – PROGRAMS 64
- APPENDIX B – PROGRAMS 65
- 60 66
- 121c POROUS 69
- 121c HOLLOW 70
- 134c EMERGENCY 73
- 134°C - 3'00'' 73
- VACUUM TEST (VT) 74
- -0.80 bar 74
- EXAMPLES OF PRINTED REPORTS 75
- APPENDIX C – MAINTENANCE 77
- QUALITY DEMINERALIZED 78
- MAINTENANCE 79
- DESCRIPTION 79
- THE COMPONENT 81
- PERIODIC 82
- STERILIZER 82
- VALIDATION 82
- DISPOSAL AT END 82
- PROVIDING THE MODEL 85
- APPENDIX E – ALARMS 86
- RESETTING THE 88
- SYSTEM 88
- ALARM CODES 89
- DICHIARAZIONE DI CONFORMITÀ 97
- TECHNICAL SUPPORT DEPARTMENT 102
© 2020, manymanuals.com. All rights reserved. | 1.724 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals