Mocom Milldrop Specifications Page 16
- Page / 102
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4. INSTALLATION
10
INSTALLATION
INTRODUCTION
The first and fundamental step in achieving good sterilizer operation, long life and complete
use of its features is a correct, careful installation. Moreover, this precaution will avoid the
danger of physical injury or property damage, not to mention malfunctions and damage to the
machine. So, please follow the instructions in this chapter scrupulously.
NOTE
M.O.COM.
CUSTOMER SUPPORT (SEE
A
PPENDIX Z) WILL ANSWER YOUR QUESTIONS
AND PROVIDE ADDITIONAL INFORMATION
.
T
HE STERILIZER HAS PASSED ALL REQUIRED INSPECTIONS BEFORE BEING PLACED ON
THE MARKET
. IT DOES NOT REQUIRE ANY ADDITIONAL CALIBRATION BEFORE BEING
PLACED IN SERVICE
.
Dimensions and weight
B and B+ B
2
A. Height (total) 420 mm 420 mm
B. Width (total) 480 mm 480 mm
C. Depth (excluding rear
connections)
560 mm 660 mm
Total weight 58 kg 63 kg
Electricity
The electrical system to which the sterilizer will be connected must be suitably dimensioned
based on the electrical characteristics of the device. This information is shown on the back of
the machine.
COMPARTMENT
DIMENSIONS FOR
BUILT-IN
INSTALLATIONS
When installing the sterilizer inside a cabinet, you must
provide adequate space all around the device to
provide effective ventilation as well as a large enough
opening in the back that, in addition to allowing the
passage of the power cord will also provide an
adequate air flow and the consequent optimum cooling
of the heat exchanger.
The compartment where the steriliser will be kept must
have the following minimum dimensions:
Dimensions and weight
B and B+ B
2
A. Height 500 mm 500 mm
B. Width 580 mm 580 mm
C. Depth 600 mm 700 mm
WARNING
COMPARTMENT DIMENSIONS LESS THAN THOSE SHOWN MAY
COMPROMISE THE CORRECT CIRCULATION OF AIR AROUND THE
DEVICE AND MAY NOT PROVIDE ADEQUATE COOLING, WITH THE
CONSEQUENT DETERIORATION OF PERFORMANCE AND/OR POSSIBLE
DAMAGE.
NOTE
I
F THE MAIN SWITCH IS INACCESSIBLE WHEN INSTALLED IN THE COMPARTMENT, USE AN
ELECTRIC PLUG THAT INCORPORATES AN ON
/OFF SWITCH.
D
O NOT REMOVE THE UPPER COVER OR ANY OTHER EXTERNAL PART. WHEN INSTALLED
IN THE COMPARTMENT
, THE DEVICE MUST BE COMPLETE WITH ALL ITS PARTS.
P
LEASE REFER TO APPENDIX A (TECHNICAL CHARACTERISTICS) FOR COMPLETE
TECHNICAL DATA
.
- REVISIONS 3
- TABLE OF CONTENTS 3
- PURPOSE OF THE 8
- MANUAL 8
- GENERAL 8
- WARNINGS 8
- CONTENTS OF 9
- THE PACKAGE 9
- HANDLING THE 10
- PRODUCT 10
- INTRODUCTION 11
- CONTROL 14
- LCD DISPLAY 14
- OPERATING 15
- CYCLE EXAMPLE 15
- INSTALLATION 16
- EXTENSION CORDS 17
- MANAGING THE 18
- FILES BY 18
- MILLFLASH SW 18
- FIRST START-UP 23
- STAND-BY MODE 24
- FILLING DISTILLED 25
- MAX LEVEL IN THE 26
- INTERNAL/ 26
- EXTERNAL DRAIN 26
- CONFIGURATION 27
- MILLENNIUM 28
- DESCRIPTION OF 29
- THE MENU ITEMS 29
- DEFAULTS 31
- SETTINGS 31
- ACTIVATING 31
- OPTIONS 31
- DISABLED+ 32
- 134 °C HOLLOW+ 33
- STANDARD DRYING+ 34
- 134°C PROCESS+ 35
- FRACTION. VACUUM + 35
- SHORT DRYING+ 35
- STANDARD DRYING+ 36
- ST‐ BY MODE+ 37
- OFF+ 37
- PRINTER+ 38
- OFF+ 38
- TYPE 1 + 38
- CR TYPE+ 38
- PRINTOUT MODE+ 39
- AT CYCLE END+ 39
- NORMAL PRINT+ 39
- AUTOMAT. FILLING + 40
- INTERNAL DRAIN+ 40
- EXIT THE 42
- PREPARING THE 43
- MATERIAL 43
- ARRANGING THE 44
- 134°C POROUS 46
- STERILIZATION CYCLE 47
- RUNNING 48
- THE CYCLE 48
- 134°C B CYCLE 49
- Standard drying 52
- Intelligent drying 52
- EXTRA DRYING 52
- (+XX) is the time 52
- RESULT OF THE 53
- CYCLE 53
- CHECK OF THE 54
- CYCLE DATA 54
- REPORT 54
- MANUAL CYCLE 54
- INTERRUPTION 54
- SEE APPENDIX E “ALARMS” 55
- STORING 56
- STERILIZED 56
- MATERIALS 56
- TEST PROGRAMS 57
- PRINTING REPORTS 58
- SUMMARY TABLE 61
- SAFETY DEVICES 62
- WATER SUPPLY CHARACTERISTICS 63
- APPENDIX B – PROGRAMS 64
- APPENDIX B – PROGRAMS 65
- 60 66
- 121c POROUS 69
- 121c HOLLOW 70
- 134c EMERGENCY 73
- 134°C - 3'00'' 73
- VACUUM TEST (VT) 74
- -0.80 bar 74
- EXAMPLES OF PRINTED REPORTS 75
- APPENDIX C – MAINTENANCE 77
- QUALITY DEMINERALIZED 78
- MAINTENANCE 79
- DESCRIPTION 79
- THE COMPONENT 81
- PERIODIC 82
- STERILIZER 82
- VALIDATION 82
- DISPOSAL AT END 82
- PROVIDING THE MODEL 85
- APPENDIX E – ALARMS 86
- RESETTING THE 88
- SYSTEM 88
- ALARM CODES 89
- DICHIARAZIONE DI CONFORMITÀ 97
- TECHNICAL SUPPORT DEPARTMENT 102
© 2020, manymanuals.com. All rights reserved. | 1.289 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals